NEW PRODUCTS
NO PREP INSTANT PRIMER & VCT TILE COATING
ArmorGarage has added some amazing new products to our product lineup. First up is our game changing epoxy primer that requires virtually no prep and can instantly be epoxy coated over. You simply need to remove any nonbondable contaminants such as surface dirt, oil, grease or rust etc. This works over dirty concrete you just need to remove any dust with a vac or leaf blower or any dirt buildups. Then simply use our Acetone resistant hand pump sprayer or one of your own and spray down the primer. Let sit for 15 minutes till it gets tacky. Then immediately apply any ArmorGarage epoxy floor coating. This primer is super high performance and cannot be separated from concrete once it cures. Apply all the epoxy within 90 minutes. You can do the floor in sections, this gives you 90 minutes for each section to ensure you apply the epoxy within the coating window. If you miss the coating window for any reason simply scuff the primer with 120 grit and reapply some primer. This amazing primer utilizes ArmorGarage epoxy technology combined with Primera Nano Technology to allow it to stick to almost anything. Great for concrete floors with exposed aggregate(small river stones at the surface) and other hard to bond to surfaces. Thus eliminating the need for shot blasting, diamond grinding or etching. Saving time and money. This is a great solution for jobs that have limited down time. See the product here: https://www.armorgarage.com/noprinpr.html or contact us for help from one of our Reps.
Next up is our revolutionary VCT & Vinyl Floor Coating. Putting a permanent clear coat on VCT Tile and Vinyl Flooring has been the Holy Grail of the epoxy coating business. There are plenty of coatings that can be applied but none that will permanently adhere till now. We have gotten thousands of calls from customers that are looking to get out of the constant stripping and waxing of their vinyl floors. Stripping and waxing is time consuming and costly and must be done continuously or the your floor will start to look very shabby very quickly. ArmorGarage’s epoxy technology once again combined with Primera Nano Technology allows our clear liquified epoxy quartz coating to be sprayed onto any type of vinyl floor or linoleum and totally bond to it. Dries to a beautiful clear gloss finish that is extremely durable and easily cleaned. Eliminates scrubbing, stripping and waxing. This is a fantastic product for institutional and commercial applications in large high traffic areas where cleanliness is critical.
For more information see here https://www.armorgarage.com/vcttilivishc.html or talk to one of our expert Reps today.
It may seem like a good idea when you read about it but doing it is much harder than it sounds. First off you need a tremendous amount of flakes, 70-75lbs of flakes for a typical 2 ½ car garage. Trying to do it with less chips and your floor will come out blotchy! Then you have the problem of applying so many flakes without them piling up in uneven lumps. If you’re not experienced in applying the color flakes they will end up in uneven layers and piles. Other companies trying to sell you on this will tell you that you can scrape the chips down. Again easier said than done and even after scraping and even sanding, the floor won’t look right.
Let’s talk about bases first. Water based epoxies are your lowest quality epoxies since about 50% of the epoxy is water. So that as the epoxy dries the water evaporates out and you’re left with only about 50% of paint material on the floor. In addition to that, water based epoxies have low abrasion resistance, poor adhesion and will wear off your floor very quickly. The same applies to most solvent based epoxies, they’re just not good quality coatings. Solids based epoxies are the most expensive to make and when you apply it to your floor you get whatever percentage of solids in the epoxy onto your floor. For instance, if you apply a 100% solids epoxy, you get 100% of the epoxy onto your floor. If you apply a 90% solids epoxy, you lose 10% of the product to evaporation. Our Garage Floor epoxies are 100% solids.
Finally, 
To put it quite simply, 
Locker rooms are often known for being one of the most disgusting rooms in a building, and with good reason. We aren’t going to discuss everything that goes on in there, only that our 
Brighter: You need to see what you’re doing in a locker room – any locker room. The natural instinct would be to install more lights, but if you want to skip that part, then you might consider the benefits of an epoxy floor. It is reflective, and it will make the room seem much brighter. Not to mention a lot better looking than a floor with black grout lines and broken tiles.
When you think of concrete, you probably don’t think of it being fragile, but let’s be honest, it is. You can scratch it, crack it, and cause all sorts of other damage. Most commonly, these floors are corroded from salts or chemicals, which commonly make appearances in commercial facilities. You could be running an auto repair company, a private jet service, or 
There are obviously many different types of epoxy floor out there for you to consider, but the most important thing that you can do is choose one that is suited for the commercial industry. There are so many different types of floors that need epoxy coatings, from hangars, to show rooms, laboratories, and of course repair shops. You will find that there are more benefits than just durability, however. For example, an epoxy floor will make the room brighter, make the floor slip resistant, easier to keep and clean, and most importantly, it’s going to make the rest of your facility look better .
Car showrooms present a particular challenge in that you need to be able to park your vehicles inside them, but there is little doubt that they can cause problems for your floor. Even the sturdiest of concrete floors are going to have their fair share of difficulties, and for a few different reasons. First of all, you have to consider weight, and secondly, you need to consider the damage a vehicle could potentially do to a floor. Luckily, there are 
So what sets this coating apart from many others? Let’s start with the fact that it’s rated for up to G-650 Aircraft. Inside the kit you’re going to find all the tools you need to get started, from the 2-part epoxy base coat, to the floor prep etch solution. It’s never been easier, and it even comes with epoxy rollers to make adherence to the instructions simpler than ever.